What Are You Looking For?
|
Max. flow(m³/h) |
5.5 |
|
Rated flow(m³/h) |
3 |
|
Design pressure |
1.0MPa |
|
Max. head(m) |
45 |
|
Rated head(m) |
30 |
|
Protection class |
IP44 |
|
Voltage |
AC 220V/50Hz |
|
Max. input power |
600W |
|
Max. speed |
5000rpm |
|
Protection class |
IP44 |
|
Voltage |
AC 220V/50Hz |
|
Max. input power |
600W |
|
Max. speed |
5000rpm |
Item NO.:
PFM03-30EC Pro1. Pressurization of commercial water
2. Groundwater intake for domestic use
3. Pressurization of domestic water supply
Product certification
Products comply with CCC, GS (CE), EMC, RoHS, REACH, WRAS certification requirements.
Benefits
1. The permanent magnet synchronous motor control algorithm without position sensors effectively reduces motor vibration, decreases pump noise, and improves pump efficiency.
2. Intelligent control technology is employed, which detects motor armature current and provides feedback to control motor speed, enabling adaptive adjustment for varying operating conditions. This solution solves the issue of high energy consumption in conventional shielded pumps, resulting in highly efficient and low-noise operation.
1 Product Conditions
1.1 Media requirements
|
Use medium |
water |
|
Medium water temperature |
0℃～50℃ |
|
Medium PH value |
6.5～8.5 |
|
Medium hardness |
≤25°dH |
|
Solid impurity content in the medium |
solid impurity diameter and length direction ≤ 0.1mm, and volume ratio ≤ 0.1%. |
1.2 Use environment requirements
|
How to use |
keep the axis horizontal |
|
Altitude |
<1000m |
|
Operating environment temperature |
0℃～55℃ (no freezing phenomenon in the pipeline and water pump) |
|
Use environment humidity ≤95% |
|
1.3 Storage environment requirements
Storage ambient temperature: -20°C～60°C (no freezing in pipelines and pumps)
Storage environment humidity ≤95%
2. Product installation direction diagram
When the water pump is installed, the pump shaft must be in a horizontal position, and the pump shaft is allowed to be installed at an angle of ±5°.
The installation of the water pump in the system should ensure that the pump cavity is filled with liquid so that the water pump can operate normally.
Pipeline installation must be carried out according to the diagram, and the rubber pads should be well supported.
3. Start and stop of water pump
Start-up time: The start-up time of the water pump is less than 5s, that is, the time from power-on to maximum speed
Downtime: the pump stop time < 3s, that is, the time from when the pump is powered off to when it stops running
4. Motor type
|
Motor type: permanent magnet synchronous motor |
Enameled wire material: copper |
Magnetic steel material: NdFeB |
|
DC cold state resistance of the motor at 20°C: 3.77±5%Ω |
Insulation class: F |
|
5. Installation drawing
Tags :
Max Flow 8.5m³/h Rated Flow 6m³/h Pressure 1.0MPa Noise index ＜58dB(A)(Max flow) Max Head 28m Rated Head 22m Insulation IP55 Weight 5.7kg±5% Voltage AC 220V/50Hz Max Input Power 700W Max Rotation Speed 5000rpm
Max. flow(m³/h) 5.5 Rated flow(m³/h) 3 Design pressure 1.0MPa Max. head(m) 45 Rated head(m) 30 Protection class IP44 Voltage AC 220V/50Hz Max. input power 600W Max. speed 5000rpm Protection class IP44 Voltage AC 220V/50Hz Max. input power 600W Max. speed 5000rpm
Maximum flow(m³/h) 8 Rating flow(m³/h) 4 Maximum head(m) 42 Rating head(m) 38 Inlet pipe diameter RP1 1/4" Outlet pipe diameter NPT1" Input powwer(KW) 0.98 IP class IP42
Enclosure class IPX4D (EN 60529) Insulation class H Supply voltage 1 × 230 V ± 10 % 50 Hz, PE Digital input PWM 0–10 V Analog input 4–20 mA. 0–10 W direct current Connection bus input Modbus RTU Leakage current Leakage < 3.5 mА. Leakage current is measured in accordance with EN 60335-1 EMC Standards applied: EN61000-3-2, EN61000-6-3, EN61800-3-3, EN55014-1 and EN55014-2
Power supply voltage 220-240V 50/60Hz, PE Motor protection No external protection required IP class IP44 Insulation class H Humidity(RH) Max. 95% System pressure 1.0 MPa Compliance CE/ GS/ EMC/ LVD/RoHS/REACH Environment temperature 0～+40℃ Temperature class TF110 Liquid temperature -30～+110℃ (Glycol up to 50%) Voltage/ Frequency 230V/50HZ Pump housing Cast iron Energy(EEI) ≤0.23-Part2
Model Basic 25-20S Power 700/450/400W Max.flow 14.5/12/9.2m³/h Max head 16/13/11m Voltage/ Frequency 220/380V 3pH 50HZ Pump housing Cast iron Pumped liquid Water Insulation class H Degree of Protection IP42 Liquid temperature range 2-110℃ Max System Pressure 1.0Mpa
Maximum flow 10 m³/h Maximum head 12m Rated flow 5.5m³/h Rated head 7.5m Rated voltage AC 220-240V Rated current 1.2A Frequency 50/60Hz Maximum power 230 W Design pressure 1.0MPa Noise ＜40dB(A) Standby power ≤4W Degree of protection IP44 Surge current ＜10A Speed 1000～4900rpm Temperature class TF110 Weight of bare pump with wire 5kg±5%
Model U(V)/f(Hz) Head Q（m³/h） P（W） I(A) GPA15-7.5 III Z178 pro 230/50 7.5 2.6 60 0.50 7 2.4 52 0.45 6 2.2 39 0.35 5 2.1 33 0.30
Model Basic 32-12F Power 500W Max.flow 10.5m³/h Max head 12m Current 2.5A Voltage/ Frequency 115/230V 50HZ Pump housing Cast iron Pumped liquid Water Insulation class H Degree of Protection IP44 Liquid temperature range 2~110℃ Max System Pressure 1.0Mpa
Enclosure class IPX4D (EN 60529). Insulation class H. Supply voltage 1 × 230 V ± 10 % 50 Hz, PE Digital input PWM 0–10 V Analog input 4–20 mA. 0–10 W direct current Connection bus input Modbus RTU Leakage current Ileakage < 3.5 mА. Leakage current is measured in accordance with EN 60335-1. EMC Standards applied: EN61000-3-2, EN61000-6-3, EN61800-3-3, EN55014-1 and EN55014-2
Rated voltage 220V Rated power 550W Rated flow 2m³/h Rated current 3.46A Max. flow 6m³/h Rated head 28m Design pressure 10bar Max. head 33m Protection class IP54 Insulation class F Frequency 50Hz Vibration ＜2.8mm/s Noise ＜55dB(A) Max.power 650W
Motor protection No external protection required IP class IP44 Insulation class H Humidity(RH) Max. 95% System pressure 1.0 MPa Compliance CE/ GS/ EMC/ LVD/RoHS/REACH Environment temperature 0～+40℃ Temperature class TF110 Liquid temperature -30～+110℃ (Glycol up to 50%) Voltage/ Frequency 110/230V, 60Hz Pump housing Cast iron/Stainless steel Energy(EEI) ≤0.23-Part2
NO.1 Yanglin Road, Hi-tech Development Zone, 230088 Hefei, Anhui, P.R. China
© ANHUI SHINHOO CANNED MOTOR PUMP CO.,LTD All Rights Reserved.皖ICP备2024062579号
IPv6 
